page . 1 april 3,2013-rev.04 bc847bs-au npn general purpose dual transistor voltage 45 volts 150 mwatts features ? general purpose amplifier applications ? pnp epitaxial silicon, planar design ? lead free in comply with eu rohs 2011/65/eu directives ? green molding compound as per iec61249 std. . (halogen free) mechanical data ? case : sot-363, plastic ? terminals : solderable per mil-std-750, method 2026 ? approx. weight : 0.006 gram ? marking : 47s power absolute maximum ratings thermal characteristics note : 1.fr-5 board 1 x 0.75 x 0.062 in. 2.mounted on an fr4 pcb, single-sided copper, mini pad. parameter symbol value units collector - e mitter voltage v ceo 45 v collector - b ase voltage v cbo 50 v emitter - base voltage v ebo 6v collector current - c ontinuous i c 100 ma parameter symbol value units total device dissipation per device fr-5 board (note 1)t a =25 o c derate above 25 o c p d 300 150 3 mw mw mw/ o c thermal resistance , junction to ambient (note 2) r ? ja 550 o c/w junction temperature t j -55 to 150 o c storage temperature t stg -55 to 150 o c 0.018(0.45) 0.006(0.15) 0.010(0.25) 0.054(1.35) 0.045(1.15) 0.087(2.20) 0.074(1.90) 0.030(0.75) 0.021(0.55) 0.056(1.40) 0.047(1.20) 0.012(0.30) 0.005(0.15) 0.004(0.10) 0.000(0.00) 0.040(1.00) 0.031(0.80) 0.044(1.10) max. 0.087(2.20) 0.078(2.00) 0.010(0.25) 0.003(0.08) ? acqire quality system certificate : ts16949 ? aec-q101 qualified
page . 2 april 3,2013-rev.04 bc847bs-au electrical characteristics (t j =25 o c, unless otherwise noted) 1 2 3 6 5 4 fig.54 parameter symbol test condition min. typ. max. unit off characteristics collector - emitter breakdown voltage v (br)ceo i c =10ma 45 - - v collector - emitter breakdown voltage v (br)ces i c =10 ? a, v eb =0 50 - - v collector - base breakdown voltage v (br)cbo i c =10 ? a50--v emitter - base breakdown voltage v (br)ebo i e =1 ? a6 - - v collector cutoff current i cbo v cb =30v, v cb =30v, t a =150 o c -- 15 5 na ??? a on characteristics dc current gain h fe i c =2ma, v ce =5v 200 - 450 - collector - emitter saturation voltage v ce(sat) i c =10ma, i b =0.5ma i c =100ma, i b =5ma - - - 0.25 0.6 v base - emitter saturation voltage v be(sat) i c =10ma, i b =0.5ma i c =100ma, i b =5ma 0.6 0.8 - - 0.9 1 v base - emitter voltage v be(on) i c =2ma, v ce =5v i c =10ma, v ce =5v 580 - 660 - 700 770 mv small-signal characteristics current-gain-bandwidth product f t i c =10ma,v ce =5vdc,f=100mh z 100 - - mh z output capacitance c obo v cb =10v,f=1mh z --4.5pf noise figure nf i c =0.2ma,v ce =5vdc, r s =2k ? ,f=1.0kh z , bw=200h z - - 10 db
page . 3 april 3,2013-rev.04 bc847bs-au electrical characteristics curve i , collector current(madc) c hfe, normalized dc current gain 0.2 0.2 0.4 0.6 0.8 1.5 0.3 1.0 2.0 10 20 50 100 200 figure 1. normalized dc current gain 0.5 5.0 1.0 2.0 v =10v t=25c ce a o i , collector current(madc) c 0.5 0.2 0.3 0.7 0.1 0 0.2 0.4 0.6 0.8 1.0 v, voltage (volts) figure 2. "saturation" and " on " voltages 1.0 2.0 3.0 7.0 5.0 10 20 50 100 70 30 t=25c a o v (sat) @ i /i =10 be c b v (sat) @ i /i =10 ce c b v (on) @ v =10v be ce i= 10ma c i= 0ma c 2 0.02 0 0.4 0.8 1.2 1.6 2.0 0.1 1.0 10 20 50ma figure 3. collector saturation region i , base current (ma) b v , collector-emitter voltage (volts) ce 100ma 200ma t=25c a o -55 c to 125 c oo 0.2 i , collector current (ma) c vb, temperature coefficient (ma/ c) o figure 4. base-emitter temperature coefficient 2.8 2.4 2.0 1.6 1.0 1.2 1.0 10 100 cob cio t=25c a o 0.4 v , reverse voltage (volts) r figure 5. capacitance c, capacitance (pf) 0.6 0.8 1.0 2.0 1.0 2.0 30 50 7.0 10 4.0 10 20 40 6.0 8.0 v =10v t=25c ce a o 1.00.7 0.5 2.0 3.0 i , collector current (madc) c ft, current-gain-bandwidth product (mhz) figure 6. current-gain-bandwidth product 5.0 7.0 50 30 40 60 80 10 20 30 20 100 200 300 400
page . 4 april 3,2013-rev.04 bc847bs-au electrical characteristics curve singel pulse duty cycle, d-t1/t2 figure 7. thermal response t, time(ms) r(t), transient thermal resistance(normalized) 1.0m 100k 10k 1.0k 100 10 1.0 0 0.001 0.01 0.1 1.0 z (t)=r(t) r r =328 c/w max d curves apply for power pulse train shown read time at t t -tc=p r (t) ja ja ja 1 j(pk) (pk) jc o t1 t2 p(pk) d-0.5 0.1 0.2 0.05 0.02 0.01 bonding wire limit thermal limit second breakdown limit v , collector-emitter voltage(v) ce -1.0 -2.0 -5.0 -5.0 -10 -10 -50 -30 -45 -65 -100 -100 -200 i , collector current (ma) c figure 8. active region safe operating area t=25c a o bc558 bc557 bc556 t=25c j o 3ms 1s the safe operating area curves indicate ic-vce limits of the transistor that must be observed for reliable operation. collector load lines for specific circuits must fall below the limits indicated by the applicable curve. the data of figure 26 is based upon tj(pk)=150 c; tc or ta is variable depending upon conditions. pulse curves are valid for duty cycles to 10% prodided tj(pk) < 150 c. tj(pk) may be calculated from the data in figure 25. at high case or ambient temperatures, thermal limitations will reduce the power that can be handled to values less than the limitations imposed by the secondary break-down. o o
page . 5 april 3,2013-rev.04 bc847bs-au mounting pad layout order information ? packing information t/r - 10k per 13" plastic reel t/r - 3k per 7" plastic reel 0.018 (0.45) 0.020 (0.50) 0.075 (1.90) 0.026 (0.65) 0.026 (0.65)
page . 6 april 3,2013-rev.04 bc847bs-au part no_packing code_version bc847bs-au_r1_000a1 bc847bs-au_r2_000a1 for example : rb500v-40 _ r2 _ 00001 part no. serial number version code means hf packing size code means 13" packing type means t/r packing code xx version code xxxxx packing type 1 st code packing size code 2 nd code hf or rohs 1 st code 2 nd ~5 th code tape and ammunition box (t/b) a n/a 0 hf 0 serial number tape and reel (t/r) r 7" 1 rohs 1 serial number bulk packing (b/p) b 13" 2 tube p acking (t/p) t 26mm x tape and reel (right oriented) (trr) s 52mm y tape and reel (left oriented) (trl) l panasert t/b cathode up (pbcu) u forming f panasert t/b cathode down (pbcd) d
page . 7 april 3,2013-rev.04 bc847bs-au disclaimer ? reproducing and modifying information of the document is prohibited without permission from panjit international inc.. ? panjit international inc. reserves the rights to make changes of the content herein the document anytime without notification. please refer to our website for the latest document. panjit international inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. ? panjit international inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. ? applications shown on the herein document are examples of standard use and operation. customers are responsible in comprehending the suitable use in particular applications. panjit international inc. makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. ? the products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment, aerospace machinery et cetera. customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify panjit international inc. for any damages resulting from such improper use or sale. ? ? since panjit uses lot number as the tracking base, please provide the lot number for tracking when complaining.
|
